Hey folks, I'm wondering if someone could possibly help, I'm looking for a possible part number b4 I call ideal in the morning, I fitted an Ideal vogue 6years ago so it's generation 1 vogue c32, I also fitted a RF wireless controller (prt4) The reciever part plugs directly onto the boiler...
I`m looking to hire asap.
I feel the heating isn`t heating the room(s) up as quickly as they used to. I have about 16 radiators but only really use 4-5. The rest sit on frost free. I bled them all and apart from the bathroom towel warmer that hissed a little, all were fine. Went away 2 weeks...
Got an Ideal Vogue 40 Max
When its running in the early hours of the morning between 1am and 5am its as quiet as a mouse no issues, when its on in the daytime and evening every now and then its like a ships fog horn sounding off. It is 6 months old and has been doing it from the day it was...
Hi everyone,
My Ideal Vouge Max 26 was installed a few years back, all works fine. Its an S plan setup, but I've always been amazed that the temperature for the water tank and the central heating were the same and 'couldn't' be separated (according to the Ideal registered plumber who installed...
Hello all
Just gauging if there's any interest at all in this. I have an Ideal Vogue Gen2 S32 boiler. It's currently in use in my house since 2017. It has been serviced every year and I've never had any problems with it. In fact it seems like a great boiler, however it has now become obvious to...
Hello all,
At the start of the year I had a 32 Ideal Vogue Max fitted and all was well, it's working fine.
Problem is, I was getting floors done at the same time so I had a very limited time to notch out / felt between the pipes & joists.
I thought I got them all but, I didnt and the noise is...
HI all,
finished fitting the above boiler yesterday. Straight swap, side access flue with only the elbow off the boiler.
Gas pressure 21mbars on full chaff. (right by the supply)
when doing the co checked, minimum was as expected- 3ppm, .0.0000, and about 7,8%
Max on the other hand was 240ppm...
Hi,
Following an Anglia Water complete loss of Water Supply in Milton Keynes, I had a call from a Tenant reporting the No Water Flow Fault On the Ideal S32 Gen2.
When I arrived at the property I found the pressure in the System Loop was absolute zero. There were boiler manual papers out in the...
Had a new ideal vogue max c32 boiler fitted. The programmer has an “efficiency level” button that says it’s around 9-14%. That seems low.”, worried it’s installed incorrectly
Anyone have same issue?
Another boiler suggestion post.
4 bed detached house built 20 years ago with cavity wall insulation and double glazing. 1 bathroom and separate ensuite shower. 2 adults and 1 child.
Cold water flow is 20l/m. 16 radiators but 6 are single panel. Already have Tado which supports OpenTherm.
Want...
Hi All,
Having recently checked the efficiency level on my boiler, its giving me 43% high efficiency and 57% Super efficiency - I do not recall the readings last year, but it does appear considerably lower than previous checks. Are there any triggers for this to decrease which are "quick wins"...
Hi
I have a normal on/off thermostat connected to my Ideal Vogue Max 40 and have been looking through the installation manual (here) to see how to connect an Opentherm stat.
The instructions say "The link wire on the 230V installer room stat/timer connection gives a demand in conjunction with...
Hello, pressure dropping rapidly after being set to 1.5bar drops to 0 within a few minutes.
I’ve been round all the radiators bled them checked for leaks (none found) and re-pressurised, dropping back to zero again.
No water dripping from ceilings or around skirting boards, any suggestions, do...
Hi,
just moved into a new house with the above boiler fitted about 3 months ago.
getting to grips with setting up all the timings etc.
One thing I have noticed is that on the display even with the ch off the ch radiator on the display flashes and says on. Am I missing something or is this a...
Hi there,
I have a Vogue S32 Gen 2 in an empty rental property and noticed that the Boiler Pressure Gauge was high at about 3 bar. It may be that the old Tenants over pressured it with the filling loop, as I’ve certainly only filled it to 1.5 bar historically. I drained down the CH water...
Hi,
I have an Ideal Vogue C32 sited in the garage, with a iFlo Digistat +2 programmer and thermostat which lives in the hallway.
I initially bought a Hive, and returned it and picked up a Nest instead because of its OpenTherm support.
Can someone shed some light on the wiring, as well as...
Boiler, Ideal Vogue Gen2 C32
Honeywell Evohome with Opentherm.
Had Ideal out last year and they changed the thermistor, but this year its doing it again.
Strangely same time of year.
Suggestions last year from the installer was to remove the Evohome TRV from one radiator to act as a bypass. I...
Anyone fitting the vogue I got one at a good price and thought I would try one ? normally wouldn't pay the asking over a logic but customer went for it and the ideal touch smart thermostat , some good features on it the main display is great, easy to install , connected with wireless connection...
Hi guys looking for a bit of assistance if possible. I've got a client who is looking for an Ideal Vogue C40 gen 2 with weather compensation and a Nest gen 3 to be fitted. I've never fitted either of them before so unsure of the wiring. The Nest is not replacing any existing thermostat so I will...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.