You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
replacing
In computing, replace is a command that is used to replace one or more existing computer files or add new files to a target directory. Files with a hidden or system attribute set cannot be replaced using replace. The command lists all files that are replaced.
Hi all,
I'm installing a concrete patio out back. By the wall under the kitchen sink I have an existing P-Trap gully for the grey water from the sink, dishwasher, washing machine etc.
When I pour the concrete there won't be any chance to dig it up anymore. From my own research I get the...
Home owner looking for some advice pls. We have a megaflow system which we are considering removing as the tank takes up a lot of space and we don’t find we are using more than one shower or bath at a time.
Our plan is to do this when the current boiler needs replacing (probably in the next...
My daughter's place has a small water leak on a ground floor radiator valve. The radiator pipework is small diameter.i.e 8 or 10 mm. A plumber is coming back in a day or so to make necessary repairs. I am a little concerned as the house has a Boilermate 2000 on the upper floor and the...
I've got a non condensing Glowworm Ultimate with gravity tank and hot Water tank in a 4 bed house.
11 radiators
1 double 1400mm length
1 P+ 1400mm length
2 P+ 400mm length
7 singles 400mm
1 mains shower average water pressure
Any recommendations on combi boiler and KW?
Boiler budget...
Hi All,
I need to replace a radiator in the kitchen, the 10mm copper has split so using this opertunaty to replace it with a towel one and also need to remove both valves and make the pipes shorter.
Its a gravity fed system and the last radiator in the system , I have a bung kit, i know i can...
Hi, I seem to have lost a bleed nipple from one of my rads somehow. It’s a double rad, one side of the rad has a nipple, the other is gone and I need to bleed it to stop the bubbling noise.
How can I fix this please? Is it possible to buy a new one and if so how do I know what to ask for...
I want to replace a radiator that has a drain valve. Do I need to replace like for like and keep the drain valve in or can I replace with a thermostatic valve?
Hi,
I need to replace the O rings on the spout of my kitchen tap.
What lubricant do I need to use in order to aid fitting the new O rings.
Searched and failed again!
Replacing kitchen faucet for friend who needs to keep cost down. Something from low price range of better makers of domestic faucets, or a commercial faucet?
Hi
I seek some advice on replacing an existing regular boiler.
I currently have an old Potterton 10-16 Netaheat electronic, which is around 35 years old and still working OK. It is fitted to a std 'Y' plan system with boiler in utility room and separate hot water tank, pump, valve etc in...
Hi, I'm after some advice for a current system which I'm looking to replumb. Our house has had various extensions of heating system with newbuild extension and other additional rads over the years and now the system is inefficient and doesn't heat up consistently. In the extension, because the...
Sandy Rivers
Thread
diy
heating
heating system
poor flow
replacing
system
How do i replace the quarter turn cartridge on this cooke & lewis ricci bath mixer tap .
Normally there is a grub screw somewhere to take the handle off, but for the life of me i cannot find one on this mixer.
Any helpful suggestions would be greatfully received.
I've just replaced an Ultra SASF2 – M thermostatic shower cartridge together with the spring mechanism and the temperature sensor.
My problem is this: If I install the thermostatic cartridge together with the spring mechanism and the temp sensor (i.e. do the job properly), the shower runs warm...
Hi Guys,
I am the miserable owner of a Keston C36 boiler. It has had EVERYTHING on it replaced.
My questions is, what do I replace it with and can it be done without replacing the entire flue. The dual flue is at least 10m long and has a couple of 45 degree turns in it. Am I going to need...
Good day,
Can someone please advise me if it is possible to replace old terracotta waste pipes for PVC in a section only?
My sewage line goes downhill away from the house to the sewer main. What I assume to be an inspection shaft is at the bottom of my property.
I want to replace only a...
Hi, I have a dishwasher that needs to move further back to fit flush with the other units, as is sticking out.
What's in the way is an outflow pipe with 50mm diameter. Replacing it with a 25mm pipe would do the trick.
Pic at pipework.png hosted at TinyPic - https://tinypic.host/i/ocehtd...
We noticed some black gunk/residue on the cold water mixer hose - see photos.
I was wondering what the root cause could be and whether we should replace just the cold water mixer hose or the entire mixer tap.
Maybe there is another solution - would be great to know.
Thank you very much.
Leonid
Thread
australia
hose
issue
likely
mixer
replacing
residue
solution
tap
I needed to change waste pipes because they were just crumbling into pieces, but i am not sure how can I connect the new pipe to the one inside the wall. Many thanks
Hi guys,
Looking to replace an old shower diverter. Pictures attached. I'm from Australia if that makes any difference.
Originally when i got the house years ago there was a note to be careful when turning the shower diverter too hard. Eventually this happened and it started leaking from the...
Hi,
Have a couple of old microbore 28mm to 10mm manifolds for the central heating. Not sure of the condition on the inside of them but outside there's a fair bit of corrosion at the solder/compression joints. There not leaking so was wondering if they can be cleaned or if it's better to...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.