hi all , was having a few problems with my heating/hot water when water was put on it would heat up but also heat the radiators up so after bit off searching came up with the 3way port valve so i changed for a new one as when i looked at it when the water was on it was making a buzzing noise, so...
Hi just wondering if anyone can shed any light on an issue i'm having with my boiler..
Initially started i think after i came back of holiday and the pressure was low on my boiler after topping up everything was fine and boiler operated as normal. A day or so after however i started noticing...
Been out the trade now for sometime now, a little out of touch with the latested boilers.
I have a problem with my Ideal 30 combi boiler as follows.
Heating is fine, no hot water so replaced the turbine now working fine but the pre heater is not working and no fault codes given. Any advice...
Hi guys, please could I get some advice on this?????
Ive got an Ideal I-Mini 30 which is about 5-6 years old, very recently it has decided to loose pressure and give us the F1 fault code. I've filled it up a few times now but it seems to drop in pressure again once I've either put the heating on...
when my unvented hot water/heating system is losing pressure when it is ideal.
i have got Advantage Cylinder is manufactured in the UK by RM Cylinders and MAIN 15 HEAT boiler.
we have set the central heating and hot water turned off from 10 am to 5 pm.
when I come back and look at the...
Boiler has been fine for 8 months then the dhw started getting colder. Replaced the heat exchanger and the flow turbine and all good for three weeks and now cold dhw flowing cold again. Replaced the turbine again and the divert valve and motor and no difference. I have removed the divert motor...
I'm having issues with my ideal logic heat 18, it was showing fd error code so I replaced the flow sensor also thoroughly flushed ot the heat engine and pipe work, it will run fine on service mode but will not fire up unless the heat exchange is tapped lightly then will shut down when tapping...
Hi just wondering if anyone can shed any light on an issue i'm having with my boiler..
Initially started i think after i came back of holiday and the pressure was low on my boiler after topping up everything was fine and boiler operated as normal. A day or so after however i started noticing...
Hi having a repeating fault 1st its has presser hot water and heating work
Well last night it stayed on even after program had turned off set for 2130hrs was still on at 0230 when i hot up but it would not turn off tryed reset but came back on ended up turninging off electric to boilor .to try...
Hi. I've got an Ideal Heat 15 system and I've noticed a few of my rads need bleeding. I've located the pressure gauge which is above my cylinder and is already reading only 0.5 bar and if I bleed the rads, this pressure is going to drop further.
I've located what appears to be the filling...
Ideal logic plus 30 kw, gas rated at 21 kw net on hit water. Inlet pressure 21mb at boiler, flow rate 12 lit pm, temp 40.3 degrees. Have checked, gas valve, injectir internal boiler pipework for blockages. Fga readings fine, boiler gas rate on central heating 23.5 kw net, service mode gas rate...
Have called out BG multiple times. DHW sensor changed, new PCB and clean of DHW heat exchanger. Have Ideal boiler and keep getting L9. It happens overnight when the boiler tries to preheat hot water and doesn’t switch off. D comes on, but no taps or open(or leaking) and boiler overheats because...
I went to an ideal instinct were the hot water was cycling hot and cold. Upon inspection the flow pipe on the boiler was getting hot instantly as the hot tap was run. Indicating the divtor valve isn't moving all the way across when there is a hot water demand. I have past the job on to ideal as...
My own boiler at home has developed an intermittent fault causing an ignition lock out every week or two when there is a demand for hot water. When reset the boiler runs without issue for a week or two. This fault only occurs on HW demand, there has never been a lock out on CH demand. Ideal tech...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.