adaptor

I need a vertical adaptor for a Hermann Icon 23T boiler (installed 2001), does anyone know if I can still get hold of this? Any help appreciated! Many thanks, Tony.

When you guys powerflush where do you connect the flusher on a combi boiler? I've always connected to rad tails, made perfect sense. Just watched a video though saying its better to tee off by boiler so you flush the pipework leading up to the first rad. Most of the time though combi is in the...

Is it just me this is the second beko cooker with no female adaptor

Hello, I'd like to connect a pressure gauge to a 22mm copper water pipe. I've been thinking that I'd use a reducing tee to 15mm and then an adaptor 15mm to 1/4" female thread to keep the component count down. The problem I see is that the gauge has a 1/4" male parallel thread and the adaptor...

Custard just rang, he has moved in 4 years ago and had a damp chimney in the loft, last summer they went up on the roof but didnt find any problems but still made good the pointing, flashing etc. The problem didnt happen over summer even when the rains came. SInce the boiler has been back on...

Got to replace a leaking trap on a basin but its connected straight to 1" copper. There's a 11/4" - 1" adaptor on the waste, a 1" brass trap and then 1" copper leading god knows where. Ideally like to replace the waste and trap in 11/4" but is there a universal fitting that goes straight from...

Got a client who wants to run a shower off their bath tap...but doesn't want to remove the tap and replace with one that has a tap/shower mixer (because their bath is built into the floor, so only way to get to unscrew/replace the tap would be to rip out the bath). The tap has a standard 22mm...

Can anyone tell me what this fitting is called. It was put on not long ago onto a large lead pipe but they have come off of it with an adaptor going to 25mm blue mdpe which is feeding 5 flats. Its a right bodge up. Im going to put a 5 port manifold in but not seen one of these fittings before...

Hi all Have used one of these fittings before , but don't know what to call them. its a bent fitting that is used on a basin waste instead of connecting the trap to the slotted waste. It replaces the back nut, and then takes the wast to the rear of the unit ( like a space saver sink kit) the...

Hi all I am after a adaptor / connector to fit a lidl parkside pipe cleaning set. if anyone can find one in there local lidl store can you contact me please. many thanks

Don't suppose anyone out there has come across this infuriating company who uses non-standard sized immersion elements in their unvented cylinders? The thread is (I think!) 1 3/4" BSP where a standard one is 2 1/4". Given that I can get hold of replacement elements from PTS but they are £50...

Does anyone know where I can get such a thing? The cistern in the old toilet is 10mm. Having a nightmare on this job I am. Grr

I am in need of an extremely long flexi? my Russian client has asked to have her aquaflush on the side of the wall. so am needing around 750.ml. also, for some reason on the aqua fill it is a 1/2 inch bsp. so I need a 22mm flex with 1/2 inch tap connector. is there such a thing?

I've got a toilet to swap over in a bathroom and need to clean the inside of the cast iron soil pipe to accept a Mulitiquick. It has the usual 80 years of corrosion/scale build up and want to grind that off pretty quick to a smooth surface for the fins to seal against. I'll be against the clock...

Went to fit a old belfast sink today that had previously been removed from an old school. Normally, the connection coming of a sink is perfect for 1 1/2" Trap. But in this case, it looked like a 2 inch fittin! So I bought a 2 inch trap, and it was just a touch too small. Anyone came across...

I'm working on a bathroom. Cast Iron stack. I need to make use of an existing integrated connection. When I pulled out the old 40mm pipe the rubber adaptor that was on it is a strange size. It is about 1cm smaller in overall diameter than a normal rubber adaptor (it's about 50mm). It looks just...

im after a Schroeder valve adaptor that goes in the end of a foot pump we used to have them at bg but i cant find them anywhere anyone have any ideas ? they was really good for getting on expansion vessels hard rubber and flexible

Hi there, I just bought a dishwasher and now I want to hook up both the dishwasher and my washing machine to the cold water supply. However the plumbing was done in such a way (the outlet faces the side of the kitchen cupboard with a distance of about 1.5 inches) that there is no space for a...

Will The Kamco CP2 Circulation pump adaptor fit a Bosch pump in a Worcester 24CDi Combi boiler. This adapter is to use with a Kamco power flush machine and it goes onto the pump housing so that you do not have to remove the pump altogether.

As the title suggests, I know what I want, I'm going to have to go out to a merchant tommorrow (on a god dam sunday) and ask for one, I just wanted to be pre-armed with a name and not start some Lionel Blair "give us a clue" mimes. it's a compression fitting, a large plastic thing, I've used...