40mm

Does such a thing exist (40mm to 42mm chrome plated brass compression joint)? I'm have a nightmare trying to marry my shallow seal bath waste with existing 42mm pipe-work. Thanks in advance for any help.

40mm solvent weld waste to lead? all suggestions gratefully received :)

Any plumbers out there answer me a quick question? Trying to fit a 1 1/2" waste pipe into a 40mm bossed connector. Can't for the love of me get it to fit after being told it'll work. Do I need to remove the collar on the bossed connector or is there a trick?

Hi all, I am a small jobbing handyman. I have been asked to add a washing machine waste to an existing kitchen/bath waste in a flat, the washing machine will fit on the kitchen end rather than in the bathroom. Pipework is 40 mm int. diameter. Is it OK to plumb in a washing machine waste...

Hi I know the maximum run of 40mm waste pipe is usually 3m, however on a washing machine waste pipe running to an external gully with an open ended trap (stand pipe/hockey stick) I really can't see the problem in running it the 6m I need to, ideally there should be ground works and a new...

Hi there, I have a 40mm waste that is capped and sealed with a rubber adapter. I need to reuse this access point but I have very limited space. The capped 40mm pipe wont pull out of the rubber adapter or the rubber adapter from the soil stack. Are there any top tips for removing these? If I...

Not so cheap it will be hard work but not overkill for couple uses a month for 40mm holes. I've tried to core a few 40mm holes with this Bosch GBH 2400 2kg SDS Plus Hammer Drill 240V | NoLinkingToThis And it works but keeps locking so guess not what it's meant for. Or it's on it's way out. Or I...

can anyone advise on an easy way to fit a 40mm T Waste into an existing 40mm waste straight run... the straight run has no removable section to the left or right of the pipe... it is about 1meter long one side goes through the wall and is cemented in and runs under ground and the other end...

The nearest I can find is a 21.5mm boss from BES to downpipes (not soilpipes) anyone know of a 32 or40mm boss to guttering downpipe - suitable for uprated condensate pipe? Cheers Mark

This is a big no no, I know that but, are ther any methods for replacing the strength that has been removed by using plates or "Fish Plates" drilled and bolted through the joist.

I've taken out an old under-sink waste disposal unit and replaced it with a simple basket strainer. I now need to connect the 40mm male tail pipe of the strainer indirectly to the P-trap below and off to the side. I need an adapter to adapt the male strainer tail to plain 40mm pipe. At the...

Hello there, new boy on this page. If poss could anyone tell me if there is a reducer to go in what I call a normal 40mm waste pipe to accept a 32 mm pipe that is stuck with pipe glue as I'm aware that the outer dimensions are different. I dare say it's a stupid question but would appreciate any...

hi all. im in the middle of fitting a new bathroom in my house but i cant seem to find a trap for the sink. ive used 40mm pipes and a push 32mm waste in the sink. ive got 2 traps spare at the moment. one is 32mm both ends and the other is 40mm both ends but i cant find one with 32 to 40.maybe i...

Dear All - I amplumbing in a new bathroom on the first floor of a barn conversion withdrainage is on the west side. Had a look at Building Regs (sect H) andunderstand that I can exceed the 3m run on 40mm or 4m run on 50mm if I use anAAV. The longest run is close to 6m from his-and-hers basins on...

Hi, Does anyone know who stocks Wirquin 40mm magiflex solvent connectors? I'm up in Aberdeen and only know of B&Q locally who stock, but they're now becoming hit and miss. Cheers.

I’d like to replace a 40mm plastic sink wastepipe which runs through an external south-facing wall, then visibly along the wall and into a gully. It’s hideous, and lasted only 20 years before UV degraded it and the pipe fell to pieces. I’d like to replace this with ‘Old Skool’ copper. Is...

I will be starting my bathroom refit next week - would like some views on how to run the waste - have tried to draw a plan showing how waste will run (not brilliantly to scale ) - what I need to know is: - How should I run the wastes for the basin and shower once they exit the wall - should I...

I have been asked to insulate some outside waste pipes as these have frozen up and the inside sinks/basins no longer drain away..... (They poured boiling water over pipes to defrost and all ok).... Never insulated waste pipes before and was wondering if anyone could suggest the best sort of...

Hi I need a new 90 deg bend plastic waste pipe. Unfortunately, the pipe appears to be a non-standard make, a chap in one of the plumbing suppliers I asked said he thought it was a continental size. It is about 43 mm outside diameter. It is just too big for the screw threads to fit the standard...

Hi all, what's a good solution for fitting a radiator which is slightly smaller than the one that came out, is there a nice fitting that tails out of the radiator into a section of 15mm?!!!! I came across some fitted by British Gas, real chunky connectors but they look too much for the job.